3 Power Transformer Dealers in Goa | Distribution Transformer
Power Transformers in Goa

Power Transformers

Distribution & Power Transformers from Servomax subjected to rigorous and strict quality controls at every stage of manufacturing designed to meet

Distrbution & Power Transformers

Distrbution & Power Transformers

Subjected to rigorous and strict quality controls at every stage of manufacturing, Designed to meet latest national international standards like BIS, IS, IEC, ANSI, BS, DIN, etc., Wide range of Transformers duly tested at Central Power Research Institute, Bangalore , Bhopal Quality assurance programme available
1) Tube Mills
2) Telecom Centers
3) Rice Mills
4) Rolling Plants
5) Educational Institutions
6) Cold Storage

Industrial Transformers

It is designed for 30-35 degree C above ambient. Suitable for any kind of ambient temperature conditions.
Core is constructed from Low Loss of CRGO M-4 Grade confirming to latest standards & is fitted & clamped with special built in-house frames to reduce the magnetic noise & to make the structure rigid & robust.
Use paper covered electrolytic grade copper strip for winding. Cooling ducts are provided to keep the hot spot temperature as low as possible.
Tanks are made of M.S. Sheets with adequate bracing & stiffeners are given a coat of Epoxy Primer & Epoxy paint for better life. Both light grey & Siemens grey (RAL 7032) are available in colour.

Industrial Transformers in Goa
Dry type transformer

DRY TYPE TRANSFORMER

Dry type transformers are suitable for indoor installations in explosive atmospheric areas and populated locations such as malls, multiplex etc. These dry type transformers have F or H insulation class with or without enclosure as per the site requirement.
Dry transformers are very compact in sizes and hence suitable for basement installations in high rise buildings etc. Dry transformers are available with low losses giving savings over long service periods. Periodical vacuum cleaning of winding surface is the only maintenance. The capacity range of these iron core transformer is up to 2000 KVA with primary Voltage up to 11 KV class & secondary Voltage between 433 to 6600 Volts.

H.T. Transformer

Even after the installation of standard off circuit distribution transformer, the voltage fluctuation on the LT side persists due to limited range of voltage correction of the transformer. To control the voltage fluctuations, it is ideal to install Servo Controlled Automatic Voltage Controller either on LT side or HT side.
SERVOMAX make Transformers with built-in rolling contact type AVR suitable for indoor/outdoor installation, copper wound HT Two-in-one system is a revolutionary landmark in the industry when it comes to voltage regulation and stabilization. Even after the installation of standard distribution transformer the problem of low/high voltage on the LT side persists, resulting in improper operation of the electrical equipments, premature failure & production loss of a plant.

H.T. Transformer
H.T. Automatic Voltage Regulator

H.T. Automatic Voltage Regulator

Even after the installation of standard off circuit distribution transformer, the voltage fluctuation on the LT side persists due to limited range of voltage correction of the transformer. To control the voltage fluctuations, it is ideal to install Servo Controlled Automatic Voltage Controller either on LT side or HT side.
SERVOMAX make Transformers with built-in rolling contact type AVR suitable for indoor/outdoor installation, copper wound HT Two-in-one system is a revolutionary landmark in the industry when it comes to voltage regulation and stabilization. Even after the installation of standard distribution transformer the problem of low/high voltage on the LT side persists, resulting in improper operation of the electrical equipments, premature failure & production loss of a plant.

Furnace Transformers

Multiple Shielding Techniques employed to reduce the inter winding capacitance to below 0.005 picofarad and increases DC Isolation to over 1000 Megaohms.

Technically any transformer that has no direct current path between its primary & secondary windings provides isolation from any kind of leakage in Current, Spikes/Surges produced in the system. Provision of electrostatic shield in between primary & secondary winding depends upon its construction, specification & performance characteristics.

Isolation / Ultra Isolation Transformer are being used to protect Electronic & Sophisticated equipments, CNC Machines from the excessive line voltage transients, spikes / surges produced in the system. Electrostatic shielding helps in grounding these spikes & not allowing to pass on to the secondary side of the transformer.

Furnace Transformer



© 2019 Powertrac Corporation | Powered by Team Inertia Technologies